In the previous article we learned about Enumeration, Information Gathering, Call Spoofing. We introduced a little about the Asterisk Server. This time we will focus more on the Asterisk Manager Interface and some of the commands that can be run on the Asterisk server and we will also look at the AMI Brute force Attack.
Table of Content
- Introduction to AMI
- AMI Setup
- AMI Bruteforce Attack
- AMI Login
- AMI Help
- Enumerating SIP Users
- Enumerating Specific User
- Enable Debugging
- Enumerating Dial Plan
- Enumerating Core Settings
- Enumerating CDR (Call Detail Records)
- Enumerate Live Calls
Introduction to AMI
AMI means Asterisk Manager Interface; AMI allows the client program to connect the asterisk server and issues commands or read events using TCP port. By default, AMI port 5038.
With the Manager interface, we can control the PBX server, originate calls, check mailbox status, monitor the channels and SIP accounts, queues as well as execute Asterisk commands. We configure AMI setting by editing the config file located at etc/asterisk/manager.conf. By default, AMI is disabled, it can be enabled by making changes in manager.conf. AMI commands are called “actions”. The VOIP server generates “response”. AMI will also send “Events” containing various information messages about changes within the Asterisk.
While configuring the AMI, we can change Manager Headers and Response ID too. The manager can handle subscribes to extension status reports from all channels, which enable them to generate events when an extension or device changes state. There are lots of details in these events that may depend on the channel and device configuration. All channel’s or Trunk configuration file for more information in (/etc/asterisk/sip_custom.conf or /etc/asterisk/extensions_custom.conf)
Note: Before using AMI, make sure all the asterisk modules are loaded. If modules are not loaded the application might not send AMI actions.
The AMI setup requires that we make some configuration changes that we discussed in the Introduction. To make necessary changes, we need to log in to the VoIP server using SSH service.
Make the following changes in the file.
enabled = yes
port = 5038
secret = amp111
After saving configuration restart the VoIP server so that config change can come in effect.
Now, let’s see if we have the port 5038 running. Let’s perform a nmap scan to confirm the AMI port is opened.
nmap –p5038 192.168.1.12
As we can see that AMI is working on port 5038.
AMI Bruteforce Attack
For brute force, we create a dictionary of possible users and passwords. We are going to use the asterisk_login auxiliary for this attack.
set rhosts 192.168.1.12
set user_file /root/Desktop/unix_users.txt
set pass_file /root/Desktop/unix_passwords.txt
set stop_on_success true
Here, we can see that we can extract the AMI login username and Password. Most of the Asterisk-based VoIP server default username “admin” and password “amp111”.
Now let’s try logging on the Asterisk server using the credentials. We can use telnet for connecting to the AMI. After connecting we need to tell the AMI what kind of action we want to perform. In this instance, we are trying to login. So, after providing the action, we give the credentials and get access. Here we can see that we have the system privileges.
telnet 192.168.1.12 5038
As we don’t know much about the command that can be used to work around the Asterisk. We ran the help command to get a better understand of all the different tasks that can be performed using the AMI.
Enumerating SIP Users
Let’s enumerate the SIP User’s data, which can have the Extensions, Usernames, and their respective secrets. For this, we will need to specify the action. We use “command” as action. After specifying we ran the command that will show us the data of the SIP Users.
Command: sip show users
Here, we found the 4-sip user id’s and password.
Enumerating Specific User
We found 4 users in the previous practical. Now let’s enumerate information about one of the particular user. The action will remain the same for this as well. But we will use the username for targeting a particular user.
Command: sip show peer 2001
Here we can see the specific SIP peer details. We would be able to get the MD5 passwords if it was set to that particular user. We could also figure out the Permission this user has. We could also see the Caller ID of this user as well.
We can also find the Mail Box details, Server IP details. Here, IP means the IP network registration allowed for that user. We could see what kind of device the user uses as well.
Debugging can be used to monitor the hardware configuration and fault errors we can find, as well as observe the configuration and call handling information, code, and modules.
Command: sip set debug on
Here we can see SIP debugging enabled. If in case we do not turn off debug backend it will run until then we stop.
Enumerating Dial Plan
Asterisk based VoIP server common dial plan context from-internal it shows about call routing information.
Command: dialplan show from–internal
As we can see here to type of dial plan available by default one is from-internal-xfer and another one bad-number.
Enumerating Core Settings
It will show about all the asterisk default information, asterisk version, build options, verbosity information, start time, free memory load, AMI information, default language, call record feature,
Enumerating CDR (Call Detail Records)
CDR is the most useful service in asterisk. CDR is the system that provides one or more call records for each call depending on what version of Asterisk. It is useful for administrators who need a simple way to track what calls have taken place on the Asterisk system.
Command: cdr show status
Here we can CDR logging is enabled, as well as the database server running, CDR registered at backed to MySQL. We can enumerate the CDR database details using the following command.
The amount of time the user is connected to the database and the logs entered in the database can be observed in the screenshot below.
Command: cdr mysql status
Enumerate Live Calls
We can also enumerate the active calls and processed call list which tells us about different calls that are currently in session.
Command: core show calls
If you want to know more commands that can be used to enumerate an AMI, Please refer to the official Asterisk Wiki